qizhen0926
Guest
|
 |
3G routing using graphics text tutorial
« on: Nov 16th, 2017, 8:15pm » |
 Quote  Modify
 Remove
|
192.168.1.1 Low Price Huawei S5720 56Pc Ei Ac 10 Ge Uplink Gigabit Ethernet Switch settings interface not to go how to do? According to the long-term experience of small series, analyze the causes 192.168.1.1 to go into the interface of the router settings, mainly by the following reasons:
- router setup is not properly connected;
- local computer IP settings are not correct;
- router login settings interface 192.168.1.1 address is not correct;
usually 192.168.1.1 router interface settings can't go inside. Is the above three reasons, we can one investigation here is 192.168.1.1, the router settings interface to go into solution.
first, check the installation of wireless router,
router installation and connection of the line is not much, mainly need to pay attention to: first check the router is working (see the indicator is bright), router interface connection is normal. The router WAN port is used to connect to the cat or the external fiber broadband, and the router's LAN port is used to connect with the computer, as shown in the following picture. If
uses a wireless network, please check whether the laptop is connected to the router's wireless network, as long as the laptop connected to the wireless router network, you can open the 192.168.1.1 settings interface.
two, the local IP is set to automatically obtain
if the router installation and connection, and connect the power supply, the Grandstream H 264 Encoder Gxv3500 Ip Video Encoder in normal working condition, 192.168.1.1 is set to go into the interface, then check whether the computer will be set before the local IP, local IP address can be automatically changed perhaps, specific settings are as follows.
1, access to the computer [control panel] - [network connection], and then on the already connected network, click the right mouse button, click on the pop-up menu, click open [attribute], as shown in the following picture.
2, in the open network properties, select [Internet protocol version 4 (TCP/IPv4)], and then click on the property, as shown in the following picture.
3, if you have previously set the local IP address and DNS, here they are all changed to "automatic acquisition", after the completion of click the bottom of the "OK" to save, as shown in the following picture.
sometimes because the local IP address settings are not standardized, will lead to unable to open the router set up landing interface, the local IP and DNS address into automatic access to solve.
three, 192.168.1.1 router settings interface address is not correct
, if the exclusion of the router installation and connection and local IP address problem, then lead to 192.168.1.1 router settings interface can not enter, it is likely to be caused by landing address errors.
ordinary wireless router default login address is 192.168.1.1, but there are a lot of router login address is 192.168.0.1, also a lot of intelligent router address are different, you can look at the details of the nameplate on the surface of the label on the router, router IP will be marked with the surface, this is the default address, as shown below.
check router landing address if it is before to modify the settings interface address router, now you forget how to do? It's also very simple, as long as you can still connect to the network, open the CMD command box, and then type ipconfig /all, and then you can see the current router IP address, as shown in the following picture.
as shown above, because the router used by the router has not changed the address of 192.168.1.1, so the address is still this.
OK, introduced here, usually we have solved most of the 192.168.1.1 Grandstream 720P Small Hd Cctv Camera Gxv3615Wp Hd settings interface can not enter the fault, if the problem is still not resolved, you can try to restore the router factory settings, reset to see.
|
Sponsored by: The Fans!
Home
Help
Search
Members
Chat
Member Map
Login
Register
Reply
Add Poll
Notify of replies
Send Topic
Print